โ† Back to Tools Home | Olutil DIY Tools
๐ŸŒ English

Tile Calculator

Estimate how many tiles and boxes you need from the area to cover, the tile size, the grout gap and an allowance for cuts and wastage. Enter the area, the tile length and width, the grout gap, a wastage percentage and how many tiles come in a box. This is an approximate estimate for planning and shopping, not a quote. All processing runs locally in your browser. Your data is not uploaded to any server. 100% Local

The bathroom floor is 8 by 5 feet, the tile you fell for comes in boxes with a cryptic coverage figure, and the store assistant just asked how much wastage you want to allow. Tile ordering punishes both mistakes: run one box short and the replacement order can come from a different production run with a visible shade shift, while a pallet of leftovers sits in the garage for a decade. This calculator turns the four inputs that decide everything โ€” area, tile dimensions, grout gap and wastage allowance โ€” into a tile count with and without wastage, plus the number of boxes to buy.

The counting method is straightforward: each tile plus its share of the grout joint forms one module, so the gap is included in the arithmetic rather than ignored. Boxes are rounded up from the tile count with wastage. Below the calculator you will find a step-by-step measuring routine, a comparison table of common tile sizes with recommended joints and wastage figures, and the layout decisions that most often change the final count.

Check the box, not just the maths

Most tile boxes state a coverage figure per box in sq ft or mยฒ. When it exists, it already accounts for nominal tile size โ€” divide your area by it, add wastage, and you have a second opinion on this calculator's count before you order.

Measuring Up: Using the Tile Calculator

  1. Work out the area to cover

    For a rectangular room, multiply length by width. For L-shaped spaces, split the plan into rectangles, calculate each and add them together. Measure walls for a splashback or shower surround the same way โ€” height times width per section. If you measured in feet and inches, enter the area in square feet with the Imperial setting.

  2. Enter the tile dimensions

    Use the nominal tile size printed on the box: 30 ร— 30 cm in metric or 12 ร— 12 in imperial, with large formats such as 30 ร— 60 cm (12 ร— 24 in) or 60 ร— 60 cm (24 ร— 24 in) entered the same way. Nominal sizes are close enough to the true dimensions for counting, as long as the grout gap absorbs the small differences.

  3. Set the grout gap

    The default 3 mm (about 1/8 inch) suits most floor installations. Wall tile is often set tighter at 1.5 to 2 mm, while rustic-edge and natural stone tiles need 4 to 5 mm so the joints absorb their size variation. Each tile plus its gap is counted as one module, so wider joints slightly reduce the tile count.

  4. Choose the wastage allowance

    Start at 10 percent for a straight lay in a regular room, raise it to 15 percent for diagonal layouts and large formats, and use 15 to 20 percent for herringbone or rooms with many corners, bays and pipes. The wastage covers cuts, breakages and the spares you should keep for future repairs.

  5. Enter tiles per box and calculate

    The tiles-per-box figure is printed on every carton and varies wildly โ€” anything from 6 large-format tiles to 44 small ones. Press Calculate tiles to see the raw count, the count with wastage, and the boxes to buy rounded up. Copy the result into your order note so the batch and shade codes stay consistent.

One batch, one shade code

Tile colour shifts between production runs. Check that every box carries the same shade and calibre code before you leave the store, and buy the full quantity โ€” including your spares โ€” in a single order.

Tile Sizes, Grout Gaps and Wastage Compared

Tile format drives both the count and the allowance. Small mosaics flex around obstacles but produce far more joints; large-format tiles cut the joint count dramatically but generate bigger, less reusable offcuts. The table below lists common formats with the joint widths and wastage allowances that work in practice.

Tile formatTypical useGrout gapWastage (straight / diagonal)
30 ร— 30 cm (12 ร— 12 in)Kitchen and bathroom floors3 mm10% / 15%
30 ร— 60 cm (12 ร— 24 in)Floors, feature walls2โ€“3 mm10โ€“15% / 15%
60 ร— 60 cm (24 ร— 24 in)Open-plan living floors2โ€“3 mm10โ€“15% / 15%
Large format 120 cm+ slabsStatement walls, seamless floors2 mm15% / not recommended DIY
Wall tile 20 ร— 25 to 25 ร— 40 cmKitchen and bathroom walls1.5โ€“2 mm10% / 15%
Mosaic sheets (5 ร— 5 cm chips)Shower floors, niches, accents2 mm (built into sheet)10% / 10โ€“15%
Natural stone, rustic edgeEntryways, outdoor paths4โ€“5 mm15% / 20%

Two conversions cover most cross-market comparisons: 1 mยฒ = 10.76 sq ft, and a 30 cm tile is essentially a 12 inch one. If a box quotes coverage in square meters, multiply by 10.76 to compare with an American per-box figure.

Layout Patterns and Cutting: What Uses More Tile

Straight lay is the baseline

Grid-aligned rows waste the least because edge offcuts often drop into the opposite side of the room. Dry-lay a full row from the centre line before committing: shifting the starting point so neither wall receives a sliver narrower than half a tile makes the whole field look intentional and trims the offcut count at the same time.

Offset, diagonal and herringbone

A brick-pattern offset with half-tile shifts is nearly as efficient as a straight lay. Running bond at a third, diagonal sets and herringbone are different animals: every cut lands at an angle, offcuts rarely fit anywhere else, and experienced installers quote 15 to 20 percent wastage for those patterns. If you are tiling your first floor, the straight lay is also the most forgiving to set level.

Cutting, breaks and spares

Score-and-snap cutters handle porcelain cleanly once the tile is marked; wet saws earn their keep on large formats and hard materials. Expect a few breakages even with careful handling, and remember that holes for drains, valves and outlets eat whole tiles. The wastage percentage exists precisely so that the last tile of the job is not a panicked drive back to the store โ€” and whatever survives the install should stay boxed and labelled for future repairs.

Tile Calculator FAQ

How many 12x12 tiles do I need for 100 square feet?

A 12 ร— 12 in tile covers one square foot, so 100 sq ft takes about 100 tiles before the grout gap and wastage. With a 1/8 in gap and a 10 percent allowance, plan on roughly 112 tiles โ€” about 10 to 11 boxes if the cartons hold 10 or 11 tiles.

How much wastage should I add for tiles?

For a straight-lay pattern in a rectangular room, 10 percent is the usual allowance. Diagonal layouts need about 15 percent, herringbone and other complex patterns 15 to 20 percent, and large-format tiles benefit from 15 percent even when laid straight. Keep a few spares from the same batch for future repairs.

What grout gap should I use between tiles?

Wall tiles usually sit with a 1/16 to 1/8 in (1.5 to 3 mm) gap, floor tiles with 1/8 to 3/16 in (3 to 5 mm). Rectified-edge tiles can go tighter, while rustic-edge and natural stone tiles need wider joints to absorb size variation. Floors also need the joint to flex, so never butt tiles edge to edge.

Does the calculator include adhesive and grout quantities?

No, it counts tiles and boxes only. As rough planning figures, thin-set covers roughly 25 to 30 sq ft per 50 lb bag with a 1/4 in notched trowel, and a 10 lb bag of grout fills roughly 100 sq ft of 12 in tiles with a 1/8 in gap. Check the coverage tables on the packaging for your exact tile and trowel size.

Why buy all the tiles in one batch?

Tile colour and shading vary between production runs, and boxes from different batches can look noticeably different once laid. Buying everything in one order, checking the shade and calibre codes on every box, and mixing tiles from several boxes as you set keeps the finished surface uniform.

How do I convert between square meters and square feet for tile?

One square meter equals about 10.76 square feet. A 30 ร— 30 cm tile is essentially a 12 ร— 12 in tile covering just under one square foot including its share of the joint. The calculator accepts either system and reports the area in both, so coverage figures from any market compare directly.

Related Tools